Highlighted posts

key and lock set for 78 bronco
 
August 28, 2021   •   6 posts   •   90 views
 
Parts For Sale & Wanted
 
 

johnnyreb said — I,m looking for the key ,switch ,both doors and tailgate locks . Anyone have them? I live in W.Va. Any members from hear?

Read more »

 
Wiring diagram tank to guage 1991 Ford Bronco
 
August 24, 2021   •   6 posts   •   366 views
 
80-96 Ford Bronco Tech Support
 
 

miesk5 said — Yo Jim, Welcome! [image] Inspect Pump/Gauge Connector for corrosion, loose wires, etc, Tech Tip Guide, General; "...Many times, the Ford fuel pump hanger/sender assemblies are ...

Read more »

 
Just bought this 1986 Bronco 5.0l with manual trans, What do y'all think? (Picture Heavy!)
 
August 24, 2021   •   81 posts   •   2,393 views
 
1980 - 1996 Ford Bronco
 
 

Smafugula said — How did you diagnose that problem? It shows 93k but no idea if it's rolled or not. The backfire is pretty bad at times other times it doesn't happen. Timing has been set to 11. ...

Read more »

 
Doors and Top
 
August 26, 2021   •   2 posts   •   292 views
 
1980 - 1996 Ford Bronco
 
 

owarner40 said — I'm pretty new to this but I have a '95 Bronco and I was wondering if you could take off the doors and top like you can with the new Broncos (like a Jeep Wrangler) ?

Read more »

 
performance brake calipers?
 
August 24, 2021   •   6 posts   •   433 views
 
2nd Gen - 1978 - 1979 Ford Bronco
 
 

OX1 said — Right, For info, SVO MC is 1-1/8 bore, not sure where I came up with 1-1/4. It is still larger than stock, 1" or 79 F350 MC, 1-1/16". It is harder to push than either of those ...

Read more »

 
Are all Dennis Carpenter unassembled fenders this bad?
 
August 24, 2021   •   24 posts   •   650 views
 
66-77 Early Bronco Tech Support
 
 

chrlsful said — not a body man_ Most any pannels I get - have to B reworked a good bit. I'm some 1 who believes you MUST go back to the very initial (base) make sure where ever U R at that point ...

Read more »

 
Heater hose or pipe for Bronco 1995 5L engine
 
August 24, 2021   •   3 posts   •   342 views
 
1980 - 1996 Ford Bronco
 
 

chrlsful said — some cut either side, put in a short pipe w/OD same as ID of the cut hose & put a clamp either side. I can't C what;s goin on there but this can still B done w/a pipe having a ...

Read more »

 
Engine ID 351M/400 crankshaft image
 
August 24, 2021   •   14 posts   •   561 views
 
2nd Gen - 1978 - 1979 Ford Bronco
 
 

johnnyreb said — 400 crank shaft-markings I found on mine--toward the front of the motor

Read more »

 
What is this wire for? I found it under the floor on the drivers side of my 78 bronco. I think the wire color is light blue. Is it for a brake sensor?
 
August 30, 2021   •   1 post   •   40 views
 
2nd Gen - 1978 - 1979 Ford Bronco
 
 

johnnyreb said — I found this light blue wire. Under the frame . On the drivers side of my 78 bronco. Is it for a brake sensor? It had NO power on it .With the switch on or off.

Read more »

 
'89 engine trouble
 
August 25, 2021   •   15 posts   •   846 views
 
1980 - 1996 Ford Bronco
 
 

johnnyreb said — I bought a NEW MR GASKET PRESSURE GAUGE AND IT WAS JUNK. I was thinking .Along time ago they never used them and didn,t have any problems. It must be this NEW JUNK FUEL PUMP--MOST ...

Read more »